RA180 Integrated Amplifier – The impression of sound with eyes and ears

New Concept Class A/D Amplifier
Amplifiers have changed from Class A to AB and Class D. The high heat and low efficiency of Class A required a new design, so Class AB was developed. However, Class D has even higher efficiency and higher output than Class AB.

It also has dramatically improved the Signal-to-Noise ratio and Total Harmonic Distortion Characteristics over Class A and AB.

However, despite these advantages, due to the limitations of digital circuits, the sound quality has been evaluated as poor compared to A/AB.

The GaN (Gallium Nitride) Class AD amplifier developed by HiFi ROSE is an innovative new product. Dramatically improving on the problems of Class D.

Next Generation GaN FET-Applied Class AD Amplifiers
Class D amplifiers are theoretically completely linear at 0% distortion and 100% power efficient. It is a topology that provides the output, and to implement it, speed and accuracy must be a prerequisite. However, previous products exhibited non-linearity due to the limitation of the switching element (Silicon FET).

It was weak compared to Class A/AB in this area, which produced a soft and natural sound. It was a costly limitation.

In the HiFi ROSE RA180, this problem has been solved by new materials. Instead of low-quality Silicon FET chips, the Dead-Time was improved to 10 by applying Gallium Nitride FET chips.

This linearity pushes the limit of Class D while being soft and producing a natural sound.

4 Mono Amplifiers – Multi-Output Configuration using Modules
Each channel of the RA180 Integrated Amplifier is equipped with an AMP module specialized for stable bass and balance and a module specialized for soft treble and super tweeter area, with 2 modules.

Each AMP module supports 200W (8 Ohms) and can output up to 400W per channel. There are 2 independent modules that divide the high and low frequencies respectively, so that the speaker and, when connected, Bi-Amping has a driving force that is increased without being affected by the back electromotive force.

BTL Mode combines the output of two independent modules to produce a thicker and more balanced sound.

Treble Design that Reproduced even the Super Tweeter Area
The human hearing range is known to have an upper limit of 15 – 20KHz. So why would it be necessary to build an amp with a higher range?

Using modern research and experience it’s now perhaps a good time to question this belief. Temporary high treble can extend well beyond 20KHz. For example, the trumpet has a frequency response that expands up to 100KHz.

The Hi-Fi ROSE RA180 Integrated Amplifier has an output range of 20Hz – 50Khz, 100Khz@-3dB, 200KHz @-6dB. The frequency response range is designed to be wide so that high-resolution sound sources are not filtered. This ability might be beyond human audible range, but at a wide frequency, it faithfully plays the area. The depth and width of the sound and the realism will contribute to the expression.

Stable Power Supply
The power supply circuit, developed exclusively for the RA180 Integrated Amplifier, is designed with 4th generation SiC FET technology to provide high performance and high efficiency compared to typical Si FET.

In addition, ROSE has developed a 2.5 KW Power Factor Circuit (PFC) and a large-capacity capacitor. This is designed to allow the unit to be unaffected by sudden load fluctuations. The power unit is developed to support a damping factor of 200 and a total of 1000W of power.

As the heart of the amplifier, it is designed to produce powerful bass and soft treble faithfully.

Phono Amp with Variable EQ
The Phono amplifier section on the RA180 Integrated Amplifier has the goal of accurately reproducing the intent of the Producer.

It is designed to support a variety of record players with mid and low-frequency bass turnover and high-frequency roll-off adjustment.

Amplification of the very weak audio signal is captured from the cartridge and processed without coloring and faithfully keeping to the original sound.

Front Panel
Overview:Line Input x3, Balance x1, Phono x1, Supports a total of 5 external inputs. Volume is motorised and adjustable remotely.
Tone Control: You can control the Treble, Bass and Balance attributes.
Active Crossover: By eliminating the low frequency range, it specialised only the high frequency area and outputs it to enable clear treble playback.
Main Volume:The main volume is motorised and is adjustable remotely. Pure Direct The input signal can be bypassed without balance, tone control, and active crossover to increase the purity of the sound quality.
Speaker AB Selector: You can connect two speakers, and you can adjust the switch to select the speaker.
Power LED Brightness Adjustment Switch: Adjust the brightness on the front of the product in 3 steps.
Subsonic Switch: Block the ultra-high frequency to prevent ultra-high noise from negatively affecting the speaker.
Sound Reduction Switch:Reduce the amount of volume output to a minimum step.

Rear Panel
Overview: A power breaker was adopted to improve the conductivity of the input electricity, and the resolution of the sound quality was improved by securing a wide passage of the input.
BTL Mode:Four Mono Amplifiers are combined into two amplifier blocks, each supporting 400W (8 Ohms) output per channel.
Power Input Terminal: It adopts FURUTECH terminals milled in pure copper, optimised for audio, and delivers the purity of the input electricity without interfering with it.
Subwoofer Output Support:Connect with active subwoofer units to provide a rich bass listening experience.

Amplifier Output:
4Ω - 200 W x 4 Ch (800 W)
8Ω - 200 W x 4 Ch (800 W)
BTL Mode On: 400 W x 2 Ch (800 W)
Input Sensitivity:
Balanced Inputs:500mV (200 W x 4 Ch)
Unbalanced (Line 1,2,3) Inputs: 500mV (200 W x 4 Ch)
Phono (MM / MC) Input: 5mV / 0.5mV (200 W x 4 Ch)
Input Impedance:
- Balanced Inputs - 44kΩ
- Unbalanced (Line 1,2,3) Inputs - 47kΩ
Phono (MM / MC) Input: 47kΩ
Bandwidth (0dBr + / - | 8Ω):
- Speaker Output - 12Hz - 100Khz (@1W x 2Ch)
- H/F Speaker Output - 12Hz - 100Khz (@1W x 2Ch)
Frequency Response: (1W, +/- 1dB | 8Ω)
Speaker Output: 12Hz - 100Khz (@1W x 2Ch)
H/F Speaker Output:12Hz - 100Khz (@1W x 2Ch)
Total Harmonic Distortion:
- Balanced & Unbalanced (Line 1,2,3) Inputs - 0.005% (100W) (@200W x 4Ch)
Damping Factor:
- Speaker & H/F Speaker Outputs - >150 (@200W x 2Ch)
Signal-to-noise-Ratio (S/N):
- Balanced / Unbalanced / Phono MM - 102dB / 79db (@200W x 4ch)
Output Impedance:
- Speaker Output - 40mΩ (200W x 4ch)
Subsonic Filter with On/Off Switch:
-3dB - 50Hz (1W x 4ch)
Tone Control with On / Off Switch:
- Bass (100Hz) / Treble (10KHz) - +/- 15dB (1w x 2ch)
X-Over with On/Off Switch:
- HPF (-3dB) - 600Hz - 6KHz (1W x 2Ch - H/F Speaker Output)

Orders ship Sunday through Friday from our offices in Dubai, UAE.

In-stock products typically ship within 48 hours and should be expected to arrive in 3-4 business days. Orders outside of the UAE should be expected to arrive in 5-7 business days.

Pre-order and backorder products will state the approximate delivery timeline beside the Add To Cart button.

If you would like to place a custom order, chat with our specialists for a guided shopping experience. Once your order has been placed, a timeline will be provided depending on your order details.

- Free delivery within the UAE
- Shipping charges will be calculated upon checkout for orders outside of the UAE (Bahrain, Oman, Kuwait, Saudi Arabia & Qatar).
- Taxes and duties are calculated according to the applicable laws of the state or country an item is shipped to and are the customer's responsibility.

For additional information on shipping and our exchange & return policy visit our help center.

Installation charges are applicable and can be paid upon delivery for our clients based in Dubai.

- Installation Charges: AED 450 Per Hour
- Speaker Cables: AED 32 Per Meter
- Trunking: AED 10 Per Meter

For clients based outside of the UAE, please contact our specialists and we will share an estimate based on your requirements.